DVL EF Fireplace Owner's ManualFeaturing theBurnerTested and Listed byOMNI-Test Laboratories, Inc.Beaverton, OregonReport # 028-S-23B-5ANSI Z21.8
10 Installation (for qualified installers only)Travis Industries4041206 100-01147Hearth RequirementsMin. 3/4”Max. 15/16”6-1/4"Do not build the h
Installation (for qualified installers only) 11Travis Industries 4041206 100-01147Facing RequirementsNOTE: The combustible area above the facing must
12 Installation (for qualified installers only)Travis Industries4041206 100-01147Facing Over 1" ThickWARNING :Faces that attach with latch-hoo
Installation (for qualified installers only) 13Travis Industries 4041206 100-01147Face DimensionsFace Height Width NotesRawhide 27” 35-3/4”Victorian
14 Installation (for qualified installers only)Travis Industries4041206 100-01147Modifying the Face Angle for Rectangular FacesIf using a rectangular
Installation (for qualified installers only) 15Travis Industries 4041206 100-01147Facing and Hearth ExamplesFireplaceFace3/8" Thick Tile1/2"
16 Installation (for qualified installers only)Travis Industries4041206 100-01147Facing and Hearth Examples (continued)FireplaceFace3/8" Thick T
Installation (for qualified installers only) 17Travis Industries 4041206 100-01147Mantel Requirements• The combustible area above the facing must not
18 Installation (for qualified installers only)Travis Industries4041206 100-01147Vent Requirements• The vent must maintain the required clearance to
Installation (for qualified installers only) 19Travis Industries 4041206 100-01147Vent Installation• In addition to the requirements below, follow th
2 IntroductionTravis Industries 4041206 100-01147IntroductionWe welcome you as a new owner of a Travis Industries gas fireplace. In purchasing this f
20 Installation (for qualified installers only)Travis Industries4041206 100-01147Approved Vent ConfigurationsRestrictor PositionRemove the face (if i
Installation (for qualified installers only) 21Travis Industries 4041206 100-01147 Vertical Terminations with 0, 2, or 4 45° Offsets• Use 8” diameter
22 Installation (for qualified installers only)Travis Industries4041206 100-01147Vertical Terminations with 2 90° ElbowsThe termination must fall wit
Installation (for qualified installers only) 23Travis Industries 4041206 100-01147Horizontal Terminations with 1 Vertical ElbowThe termination must f
24 Installation (for qualified installers only)Travis Industries4041206 100-01147Horizontal Terminations with 3 Vertical ElbowsThe termination must f
Installation (for qualified installers only) 25Travis Industries 4041206 100-01147Termination Requirements (see the illustration below)! Venting term
26 Installation (for qualified installers only)Travis Industries4041206 100-01147Gas Line Requirements• The gas line must be installed in accordance
Installation (for qualified installers only) 27Travis Industries 4041206 100-01147Electrical Connection• Make sure the household breaker is shut off
28 Finalizing the InstallationTravis Industries 4041206 100-011471 Remove the glass following the directions below.Warning: The appliance must be comp
Finalizing the Installation 29Travis Industries 4041206 100-01147Glass Frame Removal and Installation (continued)The spring pin can come loose from th
Table of Contents 3Travis Industries 4041206 100-01147IntroductionIntroduction & Important Information...2Safety PrecautionsSafety Pr
30 Finalizing the InstallationTravis Industries 4041206 100-01147• If converting to propane, do so now before installing the logs (page 43).2 Install
Finalizing the Installation 31Travis Industries 4041206 100-011473 We recommend you purge the gas line at this time (with the glass removed). This al
32 Finalizing the InstallationTravis Industries 4041206 100-011478 Turn the flame adjust knob to its highest position - the flames should not be soot
Operation 33Travis Industries 4041206 100-01147Before You Begin• Read this entire manual before you use your new fireplace (especially the section &qu
34 OperationTravis Industries 4041206 100-01147Starting The Pilot FlameThe pilot flame is required to ignite the mainburners (it also plays a safety r
Operation 35Travis Industries 4041206 100-01147Starting the Fireplace for the First Time• Burn the heater at a high setting with the blower off for an
36 OperationTravis Industries 4041206 100-01147Adjusting the Blower SpeedThe blower helps transfer heat from the heater into the room. It will not tu
Maintenance 37Travis Industries 4041206 100-01147Maintaining Your Fireplace's Appearance• Fingerprints or other marks left on the optional gold s
38 MaintenanceTravis Industries 4041206 100-01147Troubleshooting TableProblem: Possible Cause: Don't Call for ServiceUntil You:Pilot Will Not Lig
Maintenance 39Travis Industries 4041206 100-01147How this Fireplace Works• This fireplace was designed with safety as the primary concern. Many of th
4 Safety PrecautionsTravis Industries 4041206 100-01147• IF YOU SMELL GAS:* Do not light any appliance* Extinguish any open flame* Do not touch a
40 MaintenanceTravis Industries 4041206 100-01147Wiring DiagramOrangeWhitePiezo IgniterThermopileRedThermocoupleCopper Co-Axial WireRedSpark Electrode
Safety Label 41Travis Industries 4041206 100-01147The safety (listing) label is on aplate chained to the gascontrol valve. A copy of thesafety label
42 Limited 7 Year WarrantyTravis Industries 4041206 100-01147To register your TRAVIS INDUSTRIES, INC. 7 Year Warranty, complete the enclosed Warranty
Optional Equipment (for qualified installers only) 43Travis Industries 4041206 100-01147LP Conversion InstructionsInstall the conversion kit prior to
44 Optional Equipment (for qualified installers only)Travis Industries4041206 100-011474 Remove the pilot orifice following the instructions below.
Optional Equipment (for qualified installers only) 45Travis Industries 4041206 100-01147
46 IndexTravis Industries 4041206 100-01147Approved Vent Configurations...20Adjusting the Blower Speed...
Safety Precautions 5Travis Industries 4041206 100-01147• Do not place clothing orother flammable items on ornear the heater. Becausethis heater can b
6 Features and SpecificationsTravis Industries 4041206 100-01147Features:- Works During Power Outages (millivolt system)- High Efficiency- Optional Th
Installation (for qualified installers only) 7Travis Industries 4041206 100-01147Installation Warnings:• Failure to follow all of the requirements ma
8 Installation (for qualified installers only)Travis Industries4041206 100-01147Fireplace Placement RequirementsMinimum Framing DimensionsA 1" c
Installation (for qualified installers only) 9Travis Industries 4041206 100-01147Corner InstallationsA typical 45° installationuses the minimum frami
Comments to this Manuals